High Quality & High Performance
- Mechanical structure for high-precision printing
・Unlike conventional models, a print table moves during printing for reducing printer unit vibration.
・Two ball screws are installed on both sides of the table to facilitate its movement.
- Mimaki’s superior print-image quality control technology
・Mimaki Advanced-pass system 4 (MAPS4) reduces banding and uneven color printing.
・Mimaki Fine Diffusion 1 (MFD1), a patented dithering technique, is incorporated in the Mimaki RIP RasterLink 6 software.
- Maximum 3.3m2/h productivity*
・Maximum printing speed. By reaching approximately twice the speed of previous models, it achieves approximately 2.6 times the productivity of competing printers in its class.
・The print area expands to 710 × 510 mm (28 × 20 in), enabling printing of size 636 × 469 mm (25 × 18.5 in); which is often used for screen printing.
*Print conditions：600 × 600 dpi; 8 Pass
- Uninterrupted printing solutions
・Realizes high-stability printing through an ink-circulating mechanism within the head.
・”NCU” automatically detects missing jets for cleaning. When cleaning fails, “NRS” automatically sets a replacement nozzle and restarts printing. This minimizes the loss of raw materials due to missing jets and automatically continues production at high quality.
- NEW UV curable ink "LUS-350"
Production Example of UJF-7151 plus
Gift & novelty
Mechanical structure achieves high-precision printing
Adopted a unique ball screw type head conveyance mechanism that had been equipped only in high-end machines. It improved the accuracy of the ink drop onto the substrate. This precise ink dot placement can prevent bandings substantially.
Furthermore, a high resolution print mode of 1,800 x 1,800 dpi has been added to achieve highly precise printing output.
High precision drop landing
Mimaki's print technologies for achieving beautiful printing
Mimaki Advanced pass System 4 (MAPS4)
Generally, swath boundaries are straight lines. Therefore, a slight misalignment between boundaries causes banding or uneven color printing. MAPS4 reduces banding and uneven color printing with blurred boundaries similar to gradation printing.
Banding and uneven color printing are reduced by scattering swath boundaries. Beautiful print image is obtained.
Bandings appear on swath boundaries. Print quality is remarkably degraded because banding is recognizable on each boundary.
MFD1—Mimaki Fine Diffusion 1
Dithering is an image processing technique, which transforms image data for inkjet printing. Pattern and error-diffusion dithering may, however, generate particular image noise resulting in uneven color printing or tone jumps, even on a high-performance printing unit.
The newly developed RasterLink 6 software,*1 incorporating the patented*2 image-processing MFD1, reduces noises due to dithering through hybrid processing of pattern- and error-diffusion dithering, thereby enhancing printing quality.
*1 MFD1 is available for Version 4.0 and higher
*2 Patent number: 5230816
Maximum 3.3m2/h* productivity
An array of six staggered printheads increases the printing speed and achieves top-level productivity in the same product category. The UJF-7151 plus supports effective production through high-speed printing at approximately twice the speed of previous models and approximately 2.6 times that of competitive models. Furthermore, by expanding the print area to 710 × 510 mm (28 × 20 in), it is possible to print at the size of 636 × 469 mm (25 × 18.5 in), which is often used for screen printing.
*Print conditions：600 × 600 dpi; 8 Pass
Reliable operating support package
Ink and media shortage, clogged nozzles, and other minor problems influence stable productivity.
The UJF-7151 plus fully supports continuous printing with reliable technologies.
New printhead’s ink-circulation system reduces clogging nozzles
The ink-circulation system in the head reduces ink settling and thus provides stable ink jetting. In addition, this system removes air bubbles, which plug the nozzle.. Thanks to this function, the nozzle-cleaning frequency is reduced, and accordingly, cost-effective stable printing is achieved.
NCU automatically detects and recovers clogged nozzles
Clogged nozzles are detected automatically by monitoring ink droplets with sensors. When clogged nozzles are located, these are automatically cleaned, reducing waste printing. Nozzles are checked per transfer file.
NRS for maintaining productivity
If the clogged nozzles are not recovered after cleaning through the NCU function, the NRS selects substitute nozzles and then restarts printing. This is a significant novelty, since previously, when nozzle cleaning fails, the printhead has to be repaired by a technician, and the printing operation ceases until the printhead is repaired. The NRS* allows the printer to continue printing without interruption by using non-defective nozzles as substitutes for defective nozzles until the technician arrives.*
*NRS may not be activated depending on print modes.
|Printhead||On-demand piezo head (6 staggered printheads)|
|Maximum print resolution||1,200 dpi|
|Maximum printable area||710 × 510 mm (28 × 20 in)|
|Ink||Type/Color||LH-100 (C, M, Y, K, W, Cl)
LUS-120 (C, M, Y, K, W, Cl)
LUS-350 (C, M, Y, K, W, Cl)
|Package size||1L bottle|
|Media||Size||730 × 530 mm (28.7 × 20.9 in) or smaller|
|Height||153 mm (6 in) or less|
|Weight||10 kg (22 lb) or less|
|Certifications||VCCI class A, FCC class A, ETL UL 60950-1
CE Marking (EMC, Low voltage, Machinery directive, and RoHS),
CB, REACH, Energy Star
|Interface||USB 2.0 Hi-speed / Ethernet 1000BASE-T|
|Power supply||Single-phase AC100 – 120V / AC200 – 240V|
|Operational environment||Temperature: 15 – 30 °C (59 - 86 °F)
Humidity: 35 – 65% Rh (Non condensing)
Recommended temperature range for stable operation: 20 – 25 °C (68 - 77 °F)
|Dimensions (W × D × H)||2,198 × 1,572 × 1,273 mm|
|Weight||317 kg (Base stand weight is included)|
・Inks would not be cured when printing speed is faster than that of draft mode.
- Some of the screens and printing samples in this website are artificial renderings.
- Specifications are subject to change without notice.
- All trademarks or registered trademarks are the property of their respective owners.
- Inkjet printers print using extremely fine dots, thus colors may vary slightly following replacement of the printing heads. Also note that if using multiple printer units, colors may vary slightly among the units due to slight individual differences among the units.
Inks and substrates:
- Please note that properties and adhesion, weather resistance etc. of ink and substrates can vary. Therefore please test materials before printing.
- Some substrates require primer before printing. Please test materials beforehand or ask your sales representative.
You are dealing with UV light sources that may harm your health. Please follow below guidelines strictly:
- Do not look directly into the UV light source nor place your hand, or expose your skin directly to the UV light source.
- Depending upon print mode, there might occur some VOC emittance from printed parts not yet cured and hardened.
- In addition, please read the instructions and guidelines of the manual carefully and follow those.